[ClusterLabs] corosync SCHED_RR stuck at 100% cpu usage with kernel 4.19, priority inversion/livelock?
Christine Caulfield
ccaulfie at redhat.com
Fri Feb 15 09:31:32 UTC 2019
On 14/02/2019 17:33, Edwin Török wrote:
> Hello,
>
> We were testing corosync 2.4.3/libqb 1.0.1-6/sbd 1.3.1/gfs2 on 4.19 and
> noticed a fundamental problem with realtime priorities:
> - corosync runs on CPU3, and interrupts for the NIC used by corosync are
> also routed to CPU3
> - corosync runs with SCHED_RR, ksoftirqd does not (should it?), but
> without it packets sent/received from that interface would not get processed
> - corosync is in a busy loop using 100% CPU, never giving a chance for
> softirqs to be processed (including TIMER and SCHED)
>
Can you tell me what distribution this is please? There are patches to
libqb that should be applied to fix a similar problem in 1.0.1-6 - but
that's a RHEL version and kernel 4.19 is not a RHEL 7 kernel, so I just
need to be sure that those fixes are in your libqb before going any further.
Without doubt this is a bug, in normal operation corosync is quite light
on CPU.
Chrissie
> This appears to be a priority inversion problem, if corosync runs as
> realtime then everything it needs (timers...) should be realtime as
> well, otherwise running as realtime guarantees we'll miss the watchdog
> deadline, instead of guaranteeing that we process the data before the
> deadline.
>
> Do you have some advice on what the expected realtime priorities would
> be for:
> - corosync
> - sbd
> - hard irqs
> - soft irqs
>
> Also would it be possible for corosync to avoid hogging the CPU in libqb?
> (Our hypothesis is that if softirqs are not processed then timers
> wouldn't work for processes on that CPU either)
>
> Some more background and analysis:
>
> We noticed that cluster membership changes were very unstable
> (especially as you approach 16 physical host clusters) causing the whole
> cluster to fence when adding a single node. This was previously working
> fairly reliably with a 4.4 based kernel.
>
> I've increased SBD timeout to 3600 to be able to investigate the problem
> and noticed that corosync was using 100% of CPU3 [1] and I immediately
> lost SSH access on eth0 (corosync was using eth1), where eth0's
> interrupts were also processed on CPU3 (and irqbalance didn't move it).
>
> IIUC SCHED_RR tasks should not be able to take up 100% of CPU, according
> to [3] it shouldn't be allowed to use more than 95% of CPU.
>
> Softirqs were not processed at all on CPU3 (see [2], the numbers in the
> CPU3 column did not change, the numbers in the other columns did).
> Tried decreasing priority of corosync using chrt to 1, which didn't
> help. I then increased the priority of ksoftirqd to 50 using chrt, which
> immediately solved the CPU usage problem on corosync.
>
> I tried a simple infinite loop program with realtime priority, but it
> didn't reproduce the problems with interrupts getting stuck.
>
>
> Three problems here:
> * all softirqs were stuck (not being processed) on CPU3, which included
> TIMER and SCHED. corosync relies quite heavily on timers, would lack of
> processing them cause the 100% CPU usage?
> * is there a kernel bug introduced between 4.4 - 4.19 that causes
> realtime tasks to not respect the 95% limit anymore? This would leave 5%
> time for IRQs, including NIC IRQs
> * if corosync runs at higher priority than the kernel softirq thread
> processing NIC IRQ how is corosync expecting incoming packets to be
> processed, if it is hogging the CPU by receiving, polling and sending
> packets?
>
> On another host which exhibited the same problem I've run strace (which
> also had the side-effect of getting corosync unstuck from 100% CPU use
> after strace finished):
> 1 bind
> 5 close
> 688 epoll_wait
> 8 futex
> 1 getsockname
> 3 ioctl
> 1 open
> 3 recvfrom
> 190 recvmsg
> 87 sendmsg
> 9 sendto
> 4 socket
> 6 write
>
> On yet another host I've run gdb while corosync was stuck:
> Thread 2 (Thread 0x7f6fd0c9b700 (LWP 16245)):
> #0 0x00007f6fd34a0afb in do_futex_wait.constprop.1 ()
> from /lib64/libpthread.so.0
> #1 0x00007f6fd34a0b8f in __new_sem_wait_slow.constprop.0 ()
> from /lib64/libpthread.so.0
> #2 0x00007f6fd34a0c2b in sem_wait@@GLIBC_2.2.5 () from
> /lib64/libpthread.so.0
> #3 0x00007f6fd3b38991 in qb_logt_worker_thread () from /lib64/libqb.so.0
> #4 0x00007f6fd349ae25 in start_thread () from /lib64/libpthread.so.0
> #5 0x00007f6fd31c4bad in clone () from /lib64/libc.so.6
>
> Thread 1 (Thread 0x7f6fd43c7b80 (LWP 16242)):
> #0 0x00007f6fd31c5183 in epoll_wait () from /lib64/libc.so.6
> #1 0x00007f6fd3b3dea8 in poll_and_add_to_jobs () from /lib64/libqb.so.0
> #2 0x00007f6fd3b2ed93 in qb_loop_run () from /lib64/libqb.so.0
> #3 0x000055592d62ff78 in main ()
>
>
> [1]
> top - 15:51:38 up 47 min, 2 users, load average: 3.81, 1.70, 0.70
> Tasks: 208 total, 4 running, 130 sleeping, 0 stopped, 0 zombie
> %Cpu0 : 0.0 us, 0.0 sy, 0.0 ni,100.0 id, 0.0 wa, 0.0 hi, 0.0 si,
> 0.0 st
> %Cpu1 : 53.8 us, 46.2 sy, 0.0 ni, 0.0 id, 0.0 wa, 0.0 hi, 0.0 si,
> 0.0 st
> %Cpu2 : 0.0 us, 0.0 sy, 0.0 ni,100.0 id, 0.0 wa, 0.0 hi, 0.0 si,
> 0.0 st
> %Cpu3 : 0.0 us, 0.0 sy, 0.0 ni,100.0 id, 0.0 wa, 0.0 hi, 0.0 si,
> 0.0 st
> %Cpu4 : 3.8 us, 0.0 sy, 0.0 ni, 96.2 id, 0.0 wa, 0.0 hi, 0.0 si,
> 0.0 st
> %Cpu5 : 0.0 us, 0.0 sy, 0.0 ni,100.0 id, 0.0 wa, 0.0 hi, 0.0 si,
> 0.0 st
> %Cpu6 : 0.0 us, 0.0 sy, 0.0 ni,100.0 id, 0.0 wa, 0.0 hi, 0.0 si,
> 0.0 st
> %Cpu7 : 0.0 us, 0.0 sy, 0.0 ni,100.0 id, 0.0 wa, 0.0 hi, 0.0 si,
> 0.0 st
> KiB Mem : 4210184 total, 3374752 free, 387380 used, 448052 buff/cache
> KiB Swap: 1048572 total, 1048572 free, 0 used. 3660276 avail Mem
>
> PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
> 16217 root rt 0 194832 92532 66128 R 104.0 2.2 2:54.00 corosync
> 24004 root 20 0 161984 4432 3696 R 4.0 0.1 0:00.02 top
>
> cat /proc/interrupts |grep eth
> 88: 2 0 0 0 0 0
> 0 0 xen-pirq -msi-x eth0
> 89: 2805 0 0 419621 0 0
> 0 0 xen-pirq -msi-x eth0-TxRx-0
> 90: 2 0 0 0 0 0
> 1 0 xen-pirq -msi-x eth1
> 91: 435 171086 0 0 0 0
> 0 0 xen-pirq -msi-x eth1-TxRx-0
>
> [2]
> watch cat /proc/softirqs
> CPU0 CPU1 CPU2 CPU3 CPU4
> CPU5 CPU6 CPU7
> HI: 1 0 0 0 0
> 0 0 0
> TIMER: 355339 786951 367148 266583 389591
> 357184 369577 374880
> NET_TX: 8 1081 1 743 1
> 1 223 5
> NET_RX: 5807 230818 2709 529755 3323
> 2598 2550 1878
> BLOCK: 8166 53 42 13 10
> 6563 21 6894
> IRQ_POLL: 0 0 0 0 0
> 0 0 0
> TASKLET: 103 6 9 85 0
> 0 0 0
> SCHED: 240428 100842 83166 51213 77824
> 77270 72074 72261
> HRTIMER: 0 0 0 0 0
> 0 0 0
> RCU: 135491 245345 139513 130591 140280
> 135094 141007 136063
>
>
> [3]
> /proc/sys/kernel/sched_rt_runtime_us
> 950000
> /proc/sys/kernel/sched_rt_period_us
> 1000000
>
> Best regards,
> --Edwin
> _______________________________________________
> Users mailing list: Users at clusterlabs.org
> https://lists.clusterlabs.org/mailman/listinfo/users
>
> Project Home: http://www.clusterlabs.org
> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
> Bugs: http://bugs.clusterlabs.org
>
More information about the Users
mailing list