[ClusterLabs] I question whether STONITH is working.

Thu Feb 16 16:42:19 UTC 2017

Klaus Wenninger <kwenning at redhat.com> wrote on 02/16/2017 03:27:07 AM:

> From: Klaus Wenninger <kwenning at redhat.com>
> To: kgaillot at redhat.com, Cluster Labs - All topics related to open-
> source clustering welcomed <users at clusterlabs.org>
> Date: 02/16/2017 03:27 AM
> Subject: Re: [ClusterLabs] I question whether STONITH is working.
> 
> On 02/15/2017 10:30 PM, Ken Gaillot wrote:
> > On 02/15/2017 12:17 PM, durwin at mgtsciences.com wrote:
> >> I have 2 Fedora VMs (node1, and node2) running on a Windows 10 
machine
> >> using Virtualbox.
> >>
> >> I began with this.
> >> http://clusterlabs.org/doc/en-US/Pacemaker/1.1-pcs/html-single/
> Clusters_from_Scratch/
> >>
> >>
> >> When it came to fencing, I refered to this.
> >> http://www.linux-ha.org/wiki/SBD_Fencing
> >>
> >> To the file /etc/sysconfig/sbd I added these lines.
> >> SBD_OPTS="-W"
> >> SBD_DEVICE="/dev/sdb1"
> >> I added 'modprobe softdog' to rc.local
> >>
> >> After getting sbd working, I resumed with Clusters from Scratch, 
chapter
> >> 8.3.
> >> I executed these commands *only* one node1.  Am I suppose to run any 
of
> >> these commands on other nodes? 'Clusters from Scratch' does not 
specify.
> > Configuration commands only need to be run once. The cluster
> > synchronizes all changes across the cluster.
> >
> >> pcs cluster cib stonith_cfg
> >> pcs -f stonith_cfg stonith create sbd-fence fence_sbd
> >> devices="/dev/sdb1" port="node2"
> > The above command creates a fence device configured to kill node2 -- 
but
> > it doesn't tell the cluster which nodes the device can be used to 
kill.
> > Thus, even if you try to fence node1, it will use this device, and 
node2
> > will be shot.
> >
> > The pcmk_host_list parameter specifies which nodes the device can 
kill.
> > If not specified, the device will be used to kill any node. So, just 
add
> > pcmk_host_list=node2 here.
> >
> > You'll need to configure a separate device to fence node1.
> >
> > I haven't used fence_sbd, so I don't know if there's a way to 
configure
> > it as one device that can kill both nodes.
> 
> fence_sbd should return a proper dynamic-list.
> So without ports and host-list it should just work fine.
> Not even a host-map should be needed. Or actually it is not
> supported because if sbd is using different node-naming than
> pacemaker, pacemaker-watcher within sbd is gonna fail.

I am not clear on what you are conveying.  On the command
'pcs -f stonith_cfg stonith create' I do not need the port= option?

Ken stated I need an sbd device for each node in the cluster (needing 
fencing).
I assume each node is a possible failure and would need fencing.
So what *is* a slot?  SBD device allocates 255 slots in each device.
These slots are not to keep track of the nodes?

Regarding fence_sbd returning dynamic-list.  The command
'sbd -d /dev/sdb1 list' returns every node in the cluster.
Is this the list you are referring to?

Thank you,

Durwin

> 
> >
> >> pcs -f stonith_cfg property set stonith-enabled=true
> >> pcs cluster cib-push stonith_cfg
> >>
> >> I then tried this command from node1.
> >> stonith_admin --reboot node2
> >>
> >> Node2 did not reboot or even shutdown. the command 'sbd -d /dev/sdb1
> >> list' showed node2 as off, but I was still logged into it (cluster
> >> status on node2 showed not running).
> >>
> >> I rebooted and ran this command on node 2 and started cluster.
> >> sbd -d /dev/sdb1 message node2 clear
> >>
> >> If I ran this command on node2, node2 rebooted.
> >> stonith_admin --reboot node1
> >>
> >> What have I missed or done wrong?
> >>
> >>
> >> Thank you,
> >>
> >> Durwin F. De La Rue
> >> Management Sciences, Inc.
> >> 6022 Constitution Ave. NE
> >> Albuquerque, NM  87110
> >> Phone (505) 255-8611
> >
> > _______________________________________________
> > Users mailing list: Users at clusterlabs.org
> > http://lists.clusterlabs.org/mailman/listinfo/users
> >
> > Project Home: http://www.clusterlabs.org
> > Getting started: 
http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
> > Bugs: http://bugs.clusterlabs.org
> 
> 
> 
> _______________________________________________
> Users mailing list: Users at clusterlabs.org
> http://lists.clusterlabs.org/mailman/listinfo/users
> 
> Project Home: http://www.clusterlabs.org
> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
> Bugs: http://bugs.clusterlabs.org

This email message and any attachments are for the sole use of the 
intended recipient(s) and may contain proprietary and/or confidential 
information which may be privileged or otherwise protected from 
disclosure. Any unauthorized review, use, disclosure or distribution is 
prohibited. If you are not the intended recipient(s), please contact the 
sender by reply email and destroy the original message and any copies of 
the message as well as any attachments to the original message.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.clusterlabs.org/pipermail/users/attachments/20170216/de1720e9/attachment-0002.html>