[Pacemaker] corosync/openais fails to start

Andrew Beekhof andrew at beekhof.net
Mon May 31 06:56:51 UTC 2010


On Thu, May 27, 2010 at 5:50 PM, Steven Dake <sdake at redhat.com> wrote:
> On 05/27/2010 08:40 AM, Diego Remolina wrote:
>>
>> Is there any workaround for this? Perhaps a slightly older version of
>> the rpms? If so where do I find those?
>>
>
> Corosync 1.2.1 doesn't have this issue apparently.  With corosync 1.2.1,
> please don't use "debug: on" keyword in your config options.  I am not sure
> where Andrew has corosync 1.2.1 rpms available.

Normal place: http://www.clusterlabs.org/rpm
People would need to explicitly specify a version when talking to yum though.

>
> The corosync project itself doesn't release rpms.  See our policy on this
> topic:
>
> http://www.corosync.org/doku.php?id=faq:release_binaries
>
> Regards
> -steve
>
>> I cannot get the opensuse-ha rpms any more so I am stuck with a
>> non-functioning cluster.
>>
>> Diego
>>
>> Steven Dake wrote:
>>>
>>> This is a known issue on some platforms, although the exact cause is
>>> unknown. I have tried RHEL 5.5 as well as CentOS 5.5 with clusterrepo
>>> rpms and been unable to reproduce. I'll keep looking.
>>>
>>> Regards
>>> -steve
>>>
>>> On 05/27/2010 06:07 AM, Diego Remolina wrote:
>>>>
>>>> Hi,
>>>>
>>>> I was running the old rpms from the opensuse repo and wanted to change
>>>> over to the latest packages from the clusterlabs repo in my RHEL 5.5
>>>> machines.
>>>>
>>>> Steps I took
>>>> 1. Disabled the old repo
>>>> 2. Set the nodes to standby (two node drbd cluster) and turned of
>>>> openais
>>>> 3. Enabled the new repo.
>>>> 4. Performed an update with yum -y update which replaced all packages.
>>>> 5. The configuration file for ais was renamed openais.conf.rpmsave
>>>> 6. I ran corosync-keygen and copied the key to the second machine
>>>> 7. I copied the file openais.conf.rpmsave to /etc/corosync/corosync.conf
>>>> and modified it by removing the service section and moving that to
>>>> /etc/corosync/service.d/pcmk
>>>> 8. I copied the configurations to the other machine.
>>>> 9. When I try to start either openais or corosync with the init scripts
>>>> I get a failure and nothing that can really point me to an error in the
>>>> logs.
>>>>
>>>> Updated packages:
>>>> May 26 14:29:32 Updated: cluster-glue-libs-1.0.5-1.el5.x86_64
>>>> May 26 14:29:32 Updated: resource-agents-1.0.3-2.el5.x86_64
>>>> May 26 14:29:34 Updated: cluster-glue-1.0.5-1.el5.x86_64
>>>> May 26 14:29:34 Installed: libibverbs-1.1.3-2.el5.x86_64
>>>> May 26 14:29:34 Installed: corosync-1.2.2-1.1.el5.x86_64
>>>> May 26 14:29:34 Installed: librdmacm-1.0.10-1.el5.x86_64
>>>> May 26 14:29:34 Installed: corosynclib-1.2.2-1.1.el5.x86_64
>>>> May 26 14:29:34 Installed: openaislib-1.1.0-2.el5.x86_64
>>>> May 26 14:29:34 Updated: openais-1.1.0-2.el5.x86_64
>>>> May 26 14:29:34 Installed: libnes-0.9.0-2.el5.x86_64
>>>> May 26 14:29:35 Installed: heartbeat-libs-3.0.3-2.el5.x86_64
>>>> May 26 14:29:35 Updated: pacemaker-libs-1.0.8-6.1.el5.x86_64
>>>> May 26 14:29:36 Updated: heartbeat-3.0.3-2.el5.x86_64
>>>> May 26 14:29:36 Updated: pacemaker-1.0.8-6.1.el5.x86_64
>>>>
>>>> Apparently corosync is sec faulting when run from the command line:
>>>>
>>>> # /usr/sbin/corosync -f
>>>> Segmentation fault
>>>>
>>>> Any help would be greatly appreciated.
>>>>
>>>> Diego
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> Pacemaker mailing list: Pacemaker at oss.clusterlabs.org
>>>> http://oss.clusterlabs.org/mailman/listinfo/pacemaker
>>>>
>>>> Project Home: http://www.clusterlabs.org
>>>> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
>>>
>
>
> _______________________________________________
> Pacemaker mailing list: Pacemaker at oss.clusterlabs.org
> http://oss.clusterlabs.org/mailman/listinfo/pacemaker
>
> Project Home: http://www.clusterlabs.org
> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
>




More information about the Pacemaker mailing list