[Pacemaker] pacemaker + cman - node names and bind address

[Andrew Beekhof]

On 5 Dec 2013, at 8:51 pm, Nikola Ciprich <nikola.ciprich at linuxbox.cz> wrote:

> Hello Digimer,
> 
> and thanks for Your reply. I understand your points, but my question
> is about something a bit different.. 
> 
> example: I have two nodes, node1 (lan address resolves to 192.168.1.1)
> and node2 (lan address resolves to 192.168.1.2).
> connected using crosslink (10.0.0.1, 10.0.0.2).
> 
> I'd like to use node1/node2 as cluster node names, but I'd like
> to have node1/node2 resolving to 192.168.1.0 addresses but
> cluster to communicate over 10.0.0.0 link.
> 
> In corosync, I was able to force this by setting bindnetaddr, but
> how can I set this in cman cluster? (I (roughly) know that corosync
> is used even in cman-based cluster, but this unimportant now, I think)
> 
> what is the clear way to achieve this?

There is some information on altname and altmulticast at the bottom of:

   https://access.redhat.com/site/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Cluster_Administration/s1-config-rrp-cli-CA.html

that might be of some use.

> 
> thanks a lot in advance
> 
> BR
> 
> nik
> 
> 
> 
> 
> 
> On Thu, Dec 05, 2013 at 02:36:36AM -0500, Digimer wrote:
>> On 05/12/13 02:28, Nikola Ciprich wrote:
>>> Hello,
>>> 
>>> not sure whether this shouldn't be asked in some different
>>> conference, if so, I'm sorry in advance..
>>> 
>>> Since this seems to be recommended solution for RHEL6 and since I
>>> need to use CLVMD, I switched my cluster from corosync + pacemaker
>>> to cman+pacemaker.
>>> 
>>> I usually use two-nodes clusters, where hostnames resolve to lan
>>> uplink addresses, and nodes are interconnected using crosslink (to
>>> be exact, multiple crosslinks with bonding).
>>> 
>>> I'd like to use hostnames as cluster node names, but I'd like
>>> cluster communication to go over crosslinks. Is there a way I could
>>> force this in cluster.conf?
>>> 
>>> cluster.conf manpage is quite brief on this..
>>> 
>>> Could somebody please give me an advice?
>>> 
>>> thanks a lot in advance
>>> 
>>> BR
>>> 
>>> nik
>> 
>> Hello,
>> 
>>  This list is fine to ask.
>> 
>>  I speak mainly as a cman user, but I will make an educated guess on
>> the pacemaker side of things.
>> 
>>  First, cman does not replace corosync. Both pacemaker and cman use
>> corosync for cluster communications and membership. The difference is
>> that cman configures and starts corosync for you, behind the scenes.
>> 
>>  The node names you set in cluster.conf's "<clusternode
>> name="an-c05n01.alteeve.ca" nodeid="1"> ... </clusternode>"
>> (an-c05n01.alteeve.ca in this case) is resolved to an IP address. This
>> IP address/subnet is then looked for of your network and, once found,
>> the associated network card is used.
>> 
>>  Generally, it's advised that you set the cluster names to match each
>> node's 'uname -n' hostname. If you did that, then the following bit of
>> bash will tell you which interface will be used for the cluster (on
>> RHEL/CentOS 6, anyway);
>> 
>> ifconfig |grep -B 1 $(gethostip -d $(uname -n)) | grep HWaddr | awk '{
>> print $1 }'
>> 
>>  Once you've identified the network, you will want to make sure that,
>> if it is bonded, it is a supported bond mode. Prior to 6.3 (iirc),
>> only mode=1 (active/passive) bonding was supported. With 6.4, mode=0
>> and mode=2 support was added. All other bond modes are not supported
>> under corosync.
>> 
>>  As for pacemaker integration; Be sure to setup stonith in pacemaker
>> and make sure it is working. Then use the 'fence_pcmk' fence agent in
>> cluster.conf itself. This way, should cman detect a node failure, it
>> will call pacemaker and ask it to fence the target node, saving you
>> from having to keep the real fencing configured in two places at once.
>> 
>> hth
>> 
>> digimer
>> 
>> -- 
>> Digimer
>> Papers and Projects: https://alteeve.ca/w/
>> What if the cure for cancer is trapped in the mind of a person without
>> access to education?
>> 
>> _______________________________________________
>> Pacemaker mailing list: Pacemaker at oss.clusterlabs.org
>> http://oss.clusterlabs.org/mailman/listinfo/pacemaker
>> 
>> Project Home: http://www.clusterlabs.org
>> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
>> Bugs: http://bugs.clusterlabs.org
>> 
> 
> -- 
> -------------------------------------
> Ing. Nikola CIPRICH
> LinuxBox.cz, s.r.o.
> 28.rijna 168, 709 00 Ostrava
> 
> tel.:   +420 591 166 214
> fax:    +420 596 621 273
> mobil:  +420 777 093 799
> www.linuxbox.cz
> 
> mobil servis: +420 737 238 656
> email servis: servis at linuxbox.cz
> -------------------------------------
> _______________________________________________
> Pacemaker mailing list: Pacemaker at oss.clusterlabs.org
> http://oss.clusterlabs.org/mailman/listinfo/pacemaker
> 
> Project Home: http://www.clusterlabs.org
> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf
> Bugs: http://bugs.clusterlabs.org

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 841 bytes
Desc: Message signed with OpenPGP using GPGMail
URL: <http://lists.clusterlabs.org/pipermail/pacemaker/attachments/20140109/b1fa126a/attachment-0002.sig>